Single-Beam NDIR Gas Analyzer
Simultaneous and continuous measurement of up to 5 components among NO, SO2, CO, CO2, CH4, and O2 in incinerators or boilers
- Compact design
- Long-term superior stability
- Easy-to-see LCD
- Optional functions include: auto calibration, concentration alarm, remote range-switching, and more.
- Hardly affected by moisture interference
Description
Specifications
| Principle | NO, SO2, CO, CO2, CH4: Non dispersive infrared sensor (single beam system) O2: built-in magnetic or galvanic sensor, or external zirconia sensor (ZFK7) |
|---|---|
| Ranges | NO: 0–200 ppm…5000 ppm SO2: 0–200 ppm…0–10 vol% CO2: 0–100 ppm…0–100 vol% CO: 0–200 ppm…0–100 vol% CH4: 0–500 ppm…0–100 vol% O2: 0–5 vol%…25 vol% Up to 2 ranges per component, switchable. Maximum range ratio 1 : 10 (excluding O2) |
| Repeatability | ±0.5% FS |
| Linearity | ±1.0% FS |
| Zero drift | ≤ ±2% FS per week |
| Span drift | ≤ ±2% FS per week |
| Response time | ≤ 60 s (90% response from gas inlet) Time depends on the number of components and range |
| Analog output | 4–20 mA DC or 0–1 V DC (max. 12 points) Instantaneous values of each component |
| Option | O2-corrected instantaneous value, O2 corrected average value, O2 average |
| Display | Backlit LCD (Japanese, English, or Chinese) with automatic light off function Instantaneous value, O2-corrected instantaneous value, O2 corrected average value, O2average, parameter setpoints |
| Range switching | by key operation, automatic, or by external contact input (option) |
| Contact input (option) | Voltage contact input (12–24 V DC, 15 mA max.) up to 9 points Range switch, auto-calibration start, output signal hold, average reset |
| Contact output (option) | SPDT relay contact (up to 15 points) Range identification, device error, calibration error, auto-calibration status, high/low limit alarm, pump ON/OFF, solenoid valve drive output for auto calibration |
| Communication (option) | RS-485 (MODBUS), USB type-B connector Reading/writing parameter values, measured values, device status |
| Flowmeter | Included |
| Gas inlet/outlet | Rc1/4 or NPT 1/4 |
| Structure | Steel casing, for indoor use |
| Operating environment | -5°C to 45°C, RH 95% or lower (no condensation) |
| Mounting | 19-inch rack mount, panel mount, or desktop |
| Power supply voltage | 100–240 V AC, 50/60 Hz, 100 VA |
| Dimensions (H x W x D) in mm | 133 x 483 x 418 (19-inch rack mount) 133 x 440 x 418 (panel mount) 149 x 440 x 418 (desktop) |
| Weight | Approx. 8 kg (5-component analyzer) |
| Certification | CE marking |
Gas conditions
| Flow rate | 0.5 L/min ±0.2 L/min |
|---|---|
| Temperature | 0–50°C |
| Pressure | ≤ 10 kPa |
| Dust | ≤ 100 μg/Nm3 with particle size ≤ 0.3 μm |
| Mist | Unallowable |
| Moisture | Below the saturation vapor density at room temperature (non condensing) Below the saturation vapor density at 2°C (non condensing) for NO, SO2, and CO of the range below 200 ppm |
| Corrosive gas | HCl ≤ 1 ppm |
